HAKKO

Search

Product Videos

Top of Products  >  Product Videos

Videos of HU-200 Auto-Soldering System

All videos

  • How to use SMD Type : Shape Tunnel; removing SOP

    1. Apply flux to the leads. 2. Warm the IC. 3. Remove it using a pick-up wire, etc.

  • How to use SMD Type : Shape Spatula; cleaning after removal of BGA

    1. Apply flux. 2. Put the tip on the P.W.B. 3. Move the tip slowly across.

  • How to use SMD Type : Shape Quad; removing QFP

    1. Apply flux to the leads. 2. Warm the IC. 3. Remove it using tweezers, etc.

  • How to use Shape K; drag soldering (QFP)

    Put the tip to the leads while laying down the entire blade and drag it slowly. Lay the blade down to thoroughly transfer sufficient heat to the pattern. NOTE: Apply flux to leads and land pads before soldering. It prevents the troubles such as solder bridge.

  • How to use Shape K; drag soldering (PTH)

    Put the tip to the leads while laying down the entire blade and drag it slowly. Lay the blade down to thoroughly transfer sufficient heat to the pattern. NOTE: Apply flux to leads and land pads before soldering. It prevents the troubles such as solder bridge.

  • How to use Shape K; correcting bridging if the bridge amount is small

    Stand the blade on edge and drag the tip slowly. Do not stand the blade up at too steep angle. Doing so will damage the P.W.B. NOTE: Please operate with clean tip.

  • How to use Shape K; correcting bridging if the bridge amount is large

    Lay the blade down and drag the tip slowly. NOTE: Please operate with clean tip.

  • How to use Shape J; drag soldering

    Lay down the end pad section and drag the tip slowly. Check the right timing to feed solder. NOTE: Apply flux to leads and land pads before soldering. It prevents the troubles such as solder bridge.

  • How to use Shape J; correcting bridging if the bridge amount is small

    Stand the tip on end and drag the tip slowly. NOTE: Please operate with clean tip.

  • How to use Shape J; correcting bridging if the bridge amount is large

    Lay down the end pad section and drag the tip slowly while putting the tip on the solder in the bridged section. NOTE: Please operate with clean tip.

  • How to use Shape D; soldering cup terminals

    Put the cut surface to the lead and terminal at one time to heat them. NOTE: Get rid of gold plating of terminal and pre-tin lead wire. It makes solder spread over the terminal easily and prevents soldering defect.

  • How to use Shape D; soldering chip parts

    Put the tip end to the land and drag the tip slowly while feeding solder. NOTE: Some IC is specified by manufacturer not to be touched electrode by tip end.

  • How to use Shape D; pre-tinning lead wire

    Put the cut surface to the lead and drag the tip slowly while feeding solder.

  • How to use Shape D; point soldering (QFP)

    Put the tip end to the leads and drag it slowly.

  • How to use Shape D; point soldering (PTH)

    Put the tip end to the land pad (PTH) and lead at one time to heat them.

  • How to use Shape D; drag soldering

    Put the tip end to the leads and drag it slowly. Check the right timing to feed solder. NOTE: Apply flux to leads and land pads before soldering. It prevents the troubles such as solder bridge.

  • How to use Shape C; drag soldering

    Put the cut surface to the leads and drag it slowly. NOTE: Apply flux to leads and land pads before soldering. It prevents the troubles such as solder bridge.

  • How to use Shape BCM or CM; drag soldering

    Feed solder on a hollow section and drag the tip along slowly. NOTE: Apply flux to leads and land pads before soldering. It prevents the troubles such as solder bridge.

  • How to use Shape BCM or CM; correcting bridging

    Clean solder left in the hollow section by a cleaning sponge, etc. and put the tip on the bridge section and drag it.

  • How to use Shape BC; drag soldering

    Put the cut surface to the leads and drag it slowly. NOTE: Apply flux to leads and land pads before soldering. It prevents the troubles such as solder bridge.

  • How to use Shape BC or C; soldering chip parts

    Put the cut surface to the land and drag the tip slowly while feeding solder. NOTE: Some IC is specified by manufacturer not to be touched electrode by tip end.

  • How to use Shape BC or C; pre-tinning lead wire

    Put the cut surface to the lead and drag the tip slowly while feeding solder.

  • How to use Shape BC or C; point soldering

    Put the tip end to the land and the through-hole at one time to heat them.

  • How to use Shape BC or C; melting and removing coil coatings

    Put the cut surface to the coil and terminal at one time to heat them.

  • How to use Shape B; soldering chip parts

    Put the tip to the land and drag the tip slowly while feeding solder. NOTE: Some IC is specified by manufacturer not to be touched electrode by tip end.

  • How to use Shape B; point soldering

    Put the tip end to the land pad and the through-hole at one time to heat them.

  • How to use Shape B; drag soldering

    Put the tip end to the leads and drag it slowly. Check the right timing to feed solder. NOTE: Apply flux to leads and land pads before soldering. It prevents the troubles such as solder bridge.