HAKKO

Search

Lineup

Top of Products  >  Desoldering / Rework Auto-Soldering System Soldering Iron Desoldering / Rework Preheater Soldering Pot Thermometer / Soldering Tester Fume Extractor Solder / Flux Static Control Tool for Lead and Wire Shrink Packaging / Heating Gun Glue Gun / Sealer Hobby  >  Hot-Air SMD Rework Station  >  FR-810B

Desoldering / Rework/Hot-Air SMD Rework Station

FR-810B

FR-810B
POINT
  • 670W high power and large volume hot air improves work efficiency
  • Vacuum pickup function for easy and safe removal of components
  • Possible to make a simple thermal profile by chain presets function

Available in:

  • Japan
  • North America
  • Europe
  • Oceania
  • Asia
  • Other Countries

High power and large air volume
Further evolution of SMD rework station

High power and large volume hot air for quick removal of components

FR-810B is the tool that can provide high power hot air and high volume airflow to rework on P.W.B. with high heat capacity.

High power and large air volume

Improving work efficiency

The high volume airflow and high output of FR-810B make it possible to perform the same work in only one-third of the time required when using a conventional model. This reduces the thermal impact on boards and components.
graph

  • The comparison of the time for the temperature of the solder joint of the component on the ceramic board to be heated to 200°C under the maximum set temperature and maximum set airflow of the hot air stations.
  • Single nozzles with an approximately 4mm diameter were used.

Improvements in FR-810B

On top of the features of FR-810, high power and large air volume, the new functions of vacuum pickup and pickup indicator have been given to FR-810B.
The 2 new functions make it possible to remove a component without damaging PWB.

New type of nozzles for improvement of temperature characteristics

The new nozzle improves work efficiency with uniform heating by hot air convection inside the nozzle which is created due to vents on the nozzle top. (Only with BGA nozzle)

New type of nozzles for improvement of temperature characteristics

Vacuum pickup function

The vacuum pickup function is to pick up a component with a suction pad and vacuum. It will pick a component only after the hot air melts solder joints. This can avoid an error to peel off the land by removing a component with excessive force.

Vacuum pickup function

Pickup indicator

By pre-setting pickup function, a component can be picked up automatically when solder is melted. At the same time, the indication comes up and the moment of picking up will be visible. Even a component and solder joints can not be seen as covered by a nozzle, easy and safe picking up is possible.

Pickup indicator

Use of the conventional HAKKO nozzles

Align the projection part, attach the conventional nozzle to the heater pipe.

Use conventional HAKKO nozzles

  • The heater pipe of FR-810 (discontinued) has two projection parts. In order to use the conventional nozzle, put the conversion adapter on the heater pipe that was included in your purchased FR-810 as one of standard accessories. Click here for details.

Simple nozzle removal and easy maintenance

Nozzles can be quickly changed for many different types of components.
In addition, conventional nozzles are compatible. Heaters can also be easily and securely replaced.

Quick-change N51 nozzles

Quick-change N51 nozzles

Simple tool-free removal and attachment.

Simple heater replacement

Simple heater replacement

Simply remove four screws to replace heater.

Timer function

Timer function is to control the time of operation.
This can help to prevent parts from overheating and can improve the overall quality of rework.

Chain presets function for making a simple thermal profile

The chain presets function is to make a simple thermal profile by combining several preset conditions. (Up to 5 steps) This can improve work efficiency a lot by standardizing work time, avoiding overheating, improving repeatability of operation, and making difficult rework jobs easy.

Presets function

Chain presets function

Auto sleep and auto shutoff functions

To ensure safety and conserve power, when the handpiece is placed in the handpiece holder, the auto sleep function will be activated and it will start cooling automatically. If the handpiece has not been removed from the handpiece holder (e.g. Using it in a rework fixture) and it has been idle for 30 minutes, auto shutoff function will be activated. It will be automatically powered off. Access to settings can be restricted by the password function.

With the use of grip fixture, board holder and bottom heater, work conditions can be controlled even more strictly.

A low cost rework system can be assembled with grip fixture, board holder and bottom heater.

Set-up example

  • Grip Fixture M

    Recommended if a bottom heater is not required or in case of use of a bottom heater other than the dedicated model for FR-811.

    Grip Fixture M
  • Board Holder

    Makes it easy to set and remove a PWB and to make fine adjustments after setting.

    Board Holder
  • Board Clip

    Accepts even irregular-shaped PWB.

    Board Clip
  • Board Support Unit

    Supports PWB from underneath to minimize warping.

    Board Support Unit