HAKKO

Search

Lineup

Top of Products  >  Soldering Iron Auto-Soldering System Soldering Iron Desoldering / Rework Preheater Soldering Pot Thermometer / Soldering Tester Fume Extractor Solder / Flux Static Control Tool for Lead and Wire Shrink Packaging / Heating Gun Glue Gun / Sealer Hobby  >  Solder Feed System  >  374

Soldering Iron/Solder Feed System

374

374
POINT

Available in:

  • Japan
  • North America
  • Europe
  • Oceania
  • Asia
  • Other Countries

Control of solder amount by feed time and feed speed

Amount of solder feed can be controlled by the combination of feed "time" and feed "speed". (Only in AUTO mode)

AUTO mode & MANUAL mode

AUTO mode To feed solder in the specified time and at the specified speed once the switch is pressed. (Only in AUTO mode)
MANUAL mode To keep feeding solder at the specified speed while the switch is pressed and held.

With the solder return mechanism

The function to draw back solder by the specified length after feeding is equipped.
It reduces the thermal impact of the high-temperature tip on solder and flux.
Set the appropriate conditions when using the product with an automatic machine.

How to use the solder return mechanism

Minimize solder and flux splash

As shown below, when solder is cut with a V-groove it enables the release of gas pressure generated by the flux, thereby suppressing splash. However, because the V-groove exposes the flux to outside air the solder cannot be stored for a long period of time.
When using solder with the HAKKO 374, you can groove the solder that you require.

One-handed soldering with no Loss of efficiency

The combination of the new tube unit and guide pipe assembly (options) achieves the one-handed soldering just like manual soldering, one hand for holding a soldering iron and the other hand for feeding solder wire.

 Introducing the new tube unit and guide pipe assembly for the best productivity

The new tube unit that feeds solder from the underside of the tip is now in the lineup.

Because the new guide pipe assembly is designed to be set at closer to the tip, the size of the iron with it is smaller than the iron with the conventional guide pipe assembly, and it improves the handling of the iron. The one-handed soldering just like manual soldering can be achieved.

  • Conventional type
  • New type
  •  The conventional type is recommended for a concave-type tip.

 Soldering with the advantage of "Heat-Bridge Effect"

The combination of the new tube unit and guide pipe assembly feeds solder from the underside of the tip and makes it possible to obtain "heat-bridge effect" in which molten solder helps heat transfer to enable ideal soldering.

What is a "Heat-Bridge"?

It is the phenomenon that the heat from the tip being transferred quickly to soldering joint area via molten solder.
It is one of the important elements to achieve good soldering.

 Easy maintenance

The maintenance of the new guide pipe assembly is easy because it will have less residue of flux fume and clogging with the residue while feeding solder from the underside of the tip.

 Easy adjustment of the solder feeding position

The position of solder feeding is critical to soldering quality. The new tube unit makes it easy to adjust the solder feeding position by holding the guide pipe assembly tightly with the two parts.
The installation on a soldering iron is simple and easy.

The design to hold the guide pipe assembly with the two parts
makes it easy to adjust the solder feeding position.

 Tip replacement without removing the tube unit

Tip can be replaced without removing the tube unit and the adjusted guide pipe assembly.
It saves the trouble of adjusting the position of solder feeding.

Quick and sure tip cleaning with FT-720

Tip cleaner FT-720

The tip cleaner FT-720 cleans a tip quickly and surely even having the guide pipe assembly on a handpiece.

The dedicated receptacle

The dedicated receptacle makes the conventional iron holder accept the iron with the new guide pipe assembly.

 

Usage/Applications

For one-handed soldering

Required optional parts

  •  Tube Unit
  •  Guide Pipe Assembly
  •  Iron Receptacle

The new type, feeding solder from the underside of the tip, is recommended for improving work efficiency.

  •  However, the conventional type is recommended for a concave-type tip.

For the applicable soldering irons, please refer to the optional parts combination table.
HAKKO 373・374 Optional Parts Combination Table

HAKKO 373・374 Optional Parts Combination Table

For two-handed soldering (Soldering with a feeder pen)

The auto-solder feed system with the feeder pen enables the control of amount of solder to feed.
It is useful for any type of soldering iron.

Required optional parts

  •  Feeder Pen
  •  Switch
Usable Solder Dia 0.6/0.65mm 0.8mm 1.0mm 1.2mm 1.6mm
Feeder Pen C1234 C1235
Switch Foot Switch B1649
Feeder Switch B2124